| |
 |

|
|
>
 |
Easily and effectively minimize SMD component
waste and costly production downtime with our
splice tapes and tools.
The major reason for using SMT splicing tape is
to minimize component loss and costly downtime
of your SMT machinery. By joining the end of one
SMD component roll with the beginning of a new
one you don’t have to interrupt the production
run. This saves you approximately 10-50
components every time you re-load the feeder.
Our high quality products; splice tapes, clips
and a wide range of tools, will help you to save
time and money. Our products are compatible with
Universal, Siemens, Panasonic, Juki, Fuji, Sony,
Europlacer, Assembleon, Mydata, I-pulse, Tenryu,
Yamaha, Philips and all other SMT placers. Deki
Tools splice tapes - the smart splice soloution.
Click on the product groups for detailed
information and pricing.
Product groups >> 
Cutting Tool is specially designed for precise
cuttng of SMD Carrier Tapes prior to splicing.
The Splice Tool has alignment pegs for cutting
through the center of the sprocket hole on the
carrier. The HRS4.4 (not shown) cuts the carrier
between the holes. Both tools are designed to
cut all sizes of carrier from 8mm to 56mm wide.
the HRS4.3 is included with the kit. The cutting
tool may be purchased optionally
The
Tape Splicing Tool is used for attaching
the end of a depleted reel of components
to the beginning of a new reel without
stopping the pick and place
machine...... Splice Tool Kit includes:
slicing tool, cutting tool, 100pcs
Slicing Tape, Cutting tool, and 100pcs
of extra long splice for wider carrier
tapes (optional use).
|
|
Cutting Tool is specially designed for
precise cutting of SMD Carrier Tapes
prior to splicing. The Tape Splice has
alignment pegs for cutting through the
center of the sprocket hole on the
carrier. The cutting tool cuts the
carrier between the holes. Both tools
are designed to cut all sizes of carrier
from 8mm to 56mm wide. the Splice Tool
is included with the kit.
|
|
Slicing
Tape. To begin the splicing procedure,
first remove protective liners from both
ends of the Slicing Tape.
|
|
Place
Splicing Tape in Tool with closed
circles over the pins.
|
|
It is
recommended to loosen the cover tape by
lifting it with a knife about 1/8-inch
(3mm) from beginning of the NEW reel.
Place the carrier tape over the pins on
the Tool.
|
|
Place
end of OLD reel over the pins to make a
near seamless joint.
|
|
Close
the jaws of the Tool. Using a sharp
knife, cut off excess Splicing Tape. Use
the alignment notch on the Tool to
steady the knife blade as you cut off
the excess Splicing Tape.
|
|
Place
narrow strip of spicing tape over the
covers of the joined tape. The narrow
splicing tape is for 8mm carrier tape.
Use the wider strip of splicing tape for
>12mm carriers tape. Extra long splicing
strips are included and are only
necessary to use on very wide carrier
tape.
|
|
The
Splicing procedure is now completed.
Remove the joined carrier tape from the
Splicing Tool and feed into pick and
place machine without line shut-down.
|
|
This
photo shows an example of the pull back
of the joined cover tape as it travels
over the spliced joint in the carrier
tape.
|
| |
-
Product Catalogue
SMT SPLICING
-
SMT SPLICING
-
Splice tapes on roll
-
Splice Cart Tapes
-
Single Splice Tapes
-
Double Splice Tapes
-
Splice and Clip
-
Splice tape with Holes
-
Tape Extenders
-
Splice Hand Tools
-
Thru-hole Splice Tapes
-
-
Stencil rolls
-
Tools
-
Kapton Tape
-
ESD Lab Coats
pic
|
|

|
|